Installation overview and site preparation

Installation overview and site preparation

Before you install or move this dryer, read the installation instructions first. The manual lists these main tasks:

• Choose the proper location.
• Level the appliance.
• Vent the appliance.
• Connect the inlet hose for steam models.
• Connect the gas or electric dryer.
• For an electric dryer, purchase a UL-listed 3-wire or 4-wire power cord kit with a UL-listed strain relief.
• Plug in the power cord.
• Run the installation test and test run.
• Refer to the Test Exhaust System section for the exhaust test.

Choose the right location

The dryer location must meet several requirements:

• The appliance must have proper exhaust installation.
• A gas dryer must be exhausted to the outdoors.
• Use an individual, grounded electrical outlet located within 2 ft. (61 cm) of either side of the appliance.
• Do not install or store the appliance where it will be exposed to water and/or weather.
• Check local code requirements. Some areas limit or do not permit dryer installation in garages, mobile homes, or sleeping quarters. If you have questions, contact your local building inspector.

Garage installation

If you install the dryer in a garage, place the appliance at least 18 inches (45.7 cm) above the floor.

• The manual says the standard pedestal height is 15 inches (38 cm).
• You need 18 inches (45.7 cm) from the garage floor to the bottom of the appliance.

Ambient temperature

Install the appliance where the temperature is over 45 °F (7 °C).

If the temperature around the appliance is too low, the appliance might not shut off at the end of an automatic cycle. This can cause longer drying times.

Flooring and leveling

The dryer should be installed and leveled on a solidly constructed floor with a maximum slope of 1 inch (2.5 cm).

• If needed, adjust the leveling legs to compensate for an uneven floor.
• A sturdy floor is necessary to support the total appliance weight when loaded.
• If other appliances will be nearby, their weight should also be considered.
• If the dryer is not level, clothes may not tumble properly and automatic sensor cycles may not work correctly.

Recessed area or closet installation

The manual provides recommended clearances for recessed areas and closets.

Recommended installation spacing includes:

• Upper ventilation opening: 2 openings totaling 48 sq. in. (310 cm²)
• Lower ventilation opening: 2 openings totaling 24 sq. in. (155 cm²)
• Distance to ventilation opening: 3 in. (76 mm)
• Overhead cabinet depth: 14 in. (356 mm)
• Distance to overhead cabinet/shelf: 18 in. (457 mm)
• Front clearance: 1 in. (25 mm)
• Depth: 30 1/8 in. (765 mm)
• Back clearance: 5 in. (127 mm)
• Side clearance: 1 in. (25 mm)
• Width: 27 in. (686 mm)
• Height of cabinet opening: 39 in. (990 mm)

The manual also says additional clearances should be considered for ease of installation and servicing, and to reduce noise transfer.

Closet ventilation requirements

Closets with doors must have both upper and lower vent openings to prevent heat and moisture buildup.

• Upper vent opening: minimum 48 sq. in. (310 cm²)
• The upper opening must be installed no lower than 6 feet above the floor.
• Lower vent opening: minimum 24 sq. in. (155 cm²)
• The lower opening must be installed no more than 1 foot above the floor.
• Vent grilles may be installed in the door, or the door may be cut at the top and bottom to create openings.
• Louvered doors with equivalent ventilation openings are also acceptable.

The manual notes that there should be at least a little space around the dryer, or any other appliance, to reduce vibration transfer. Too much vibration can cause noise, contact between appliances, paint damage, and more noise.

Important: No other fuel-burning appliance can be installed in the same closet as a dryer.

Closet installation with a stacked washer and dryer

For a recessed area or closet with a stacked washer and dryer, the manual lists these clearances:

• Upper ventilation opening: 2 openings totaling 48 sq. in. (310 cm²)
• Lower ventilation opening: 2 openings totaling 24 sq. in. (155 cm²)
• Distance to ventilation opening: 3 in. (76 mm)
• Front clearance: 1 in. (25 mm)
• Back clearance: 5 1/2 in. (140 mm)
• Top clearance to the ceiling: 6 in. (152 mm)
• Height to the top of stacked appliances: 77 1/2 in. (1968 mm)
• Side clearance: 1 in. (25 mm)
• Width: 27 in. (686 mm)

The note says this height can differ depending on the washer dimensions.

Cabinet installation

For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.

Recommended cabinet spacing includes:

• Depth of ventilation opening: 7 in. (178 mm)
• Back clearance: 5 in. (127 mm)
• Depth: 30 1/8 in. (765 mm)
• Front clearance: 1 in. (25 mm)
• Side clearance: 1 in. (25 mm)
• Width: 27 in. (686 mm)
• Clearance to top of cabinet: 9 in. (229 mm)

Before you continue

Make sure the selected location allows proper venting, access to a grounded outlet, and the clearances needed for your type of installation. Then continue with leveling, vent connection, and the rest of the installation steps.